Этот справочник создан в 2010 году. В нем описаны различные проблемы Honda Civic, теория и практика тюнинга, ремонт основных узлов.
Более 150 статей раскроют вам более простое понимание механизмов и потенциал автомобиля в целом.
Илья Серб (... - 2017) and EJ9 ADMIN TEAM (UNLIM)
Случайная статья узнай что то новое
One of the problems with oil consumption, maybe a leak from under valve cover head (cylinder head). The article describes the replacement gasket valve cover Honda Civic and the description covers in General. Applies to all D series motors, in particular D14A4 and D14A3.
standard form of an oil leak from under the cap
As I will show below, strip for engines D series (d14, d15, d16) are the same. Before starting work, be sure to get the gasket head 12, and preferably a torque wrench, WD40, high temperature sealant. The gasket is better to buy the original, I had 3 different not original (e.g. ELring) and are inferior to OEM HONDA, for example, that they did not have the thickened edge which gives additional contact with the surfaces of number D14 gasket 12341-P2A-000 and D16 CRX 12341-P08-000.Wait until the motor cools. Pull the HV wire out of the spark wells.\nUse the ratchet and the head 12, or socket 12 for loosening the bolts on the valve cover. So you have 2 big bolts and 3 short. Gently lift the valve cover, flip it over and lay it. Remove the gasket from the cover, clean the keyway from dirt using WD40 or degreaser and a rag, put a new gasket. Clean the surface of the cylinder head from the old sealant and dirt, should pay attention to the points of contact of cylinder head and mount the rocker arm (on the sides of the cylinder head). After cleaning, apply a small amount of sealant at these points, so that when pressing the sealant from getting inside the cylinder head. Wait a while and put the valve cover with attached elastic. Install the bolts but do not tighten, wait some time for the sealant drying, complete drying, usually 24 hours. Tighten the bolts from the middle. the the tightening Torque of bolts valve cover Honda Civic 10 nm padding can lead to tragic consequences.
tightening Torque: over 10 nm for example stripped bolt valve cover
cylinder head Cover Mugen for special lovers.
There are many engines, there are many options for the valve covers that is designed and built by Honda. But there is a small mark, structurally, they are all the same. Same inside, outside, the same fasteners. There is a slight difference, of course, for example, some caps have a mount for a machine and for some not. \nNot only that, the cap fit, and fit the rubber seal, gaskets between the cylinder head and the valve cover.
theCover cylinder head Honda Civic D14A4
Valve cover D16Z6 Honda Civic
Случайная статья узнай что то новое
Данная статья актуальна для автомобилей Honda выпуска 1992-2000 годов, таких как Civic EJ9, Civic EK3, CIVIC EK2, CIVIC EK4 и CIVIC FERIO (частично). Информация будет актуальна для владельцев Honda Integra в кузовах DB6, DC1, с моторами ZC, D15B, D16A.
Соц. Сети
Календарь событий
Клубные встречи
Партнеры EJ9.Ru
EJ9 и EK3 — записки инженера о Honda Civic 1998. 2010 – 2019 . Вся информация приводится для ознакомления, автор не несет ответственности за вред полученный в результате применения материалов сайта, находясь на сайте вы подтверждаете своё согласие с этим. Сделано Хондоводом для Хондоводов. Автор: Илья Серб Все изображения имеют авторство Карта сайта Honda Civic, всем VTEC!