Этот справочник создан в 2010 году. В нем описаны различные проблемы Honda Civic, теория и практика тюнинга, ремонт основных узлов.
Более 150 статей раскроют вам более простое понимание механизмов и потенциал автомобиля в целом.
Илья Серб (... - 2017) and EJ9 ADMIN TEAM (UNLIM)
Случайная статья узнай что то новое
And so, You dont find your firmware the repository PGMFI.org. If so, then take a look at your Board control unit P28 (or similar P08, P72, P06 OBD1). Under the area where you soldered an additional chip, a connector CN2, pins consists of 5-points (calculated from left to right), this connector needs to pass information from the ECU to the ECU OKI 66207. Signal type TTL. \nSimple TTL-RS232 Converter is in a separate article, and only need the channel reading on the ECU itself the ECU nothing is sent. The description for each contact I quote below, after using the app and reader is TTL you should be okay. Unsoldering the connector easily, do not forget that you first need to remove the varnish that protects the charge ECU P28 (or similar P08, P72, P06) solvent paints, for example .
TheBelow is the Pinout of CN2 connector OBD1 P28, data transmission is in the mode of half-duplex (half-duplex), for full duplex you need to eat J12, is located on the left part of the Board between white and black, vertical, circuits.
theBefore you start working on reading flash you need to program the chip, more than and how to flash w27c512 is in the article. You record special program romreader_66207, which pumps out firmware original firmware Honda Civic ECU via RS232 to the computer.
TheIf you havent installed the chips and then move up the article and follow the necessary instructions. If you are all done, check everything again before work.
theAfter that, You can now take the new chip 29C256. To modify the firmware with the help of a program, which I will discuss in the article, and flash parallel programmer. Good luck!
TheApplications that I added are property pgmfi.org, Im just another who has collected all into a single, translated, repeated, and passed the knowledge to You in Russian. So, say thanks to the guys from PGMFI.org.
theFirst you need an adapter to TTL Level. It is usually called USB-TTL USB RS232 TTL USB UART. The main thing was the interface to connect to your computer (usb or com port) and the second word TTL. Further, according to the diagram above (2nd paragraph to read in full) connect the DataLog, programs such as Crome, HondaLogger, ECUControl you will be able to watch the car. Dont forget to change the baud rate on 38400 bits. Through CROME you must turn off the processing of the checksum (Plugins-Enhancements-Remove Checksum Routine) and to include in the firmware OBD1 DataLog mode(Plugins-Enhancements-Quick Datalogger +RTP). Dont forget to sew the new firmware. In the basic firmware, no DataLog.
\nСлучайная статья узнай что то новое
Данная статья актуальна для автомобилей Honda выпуска 1992-2000 годов, таких как Civic EJ9, Civic EK3, CIVIC EK2, CIVIC EK4 и CIVIC FERIO (частично). Информация будет актуальна для владельцев Honda Integra в кузовах DB6, DC1, с моторами ZC, D15B, D16A.
Соц. Сети
Календарь событий
Клубные встречи
Партнеры EJ9.Ru
EJ9 и EK3 — записки инженера о Honda Civic 1998. 2010 – 2019 . Вся информация приводится для ознакомления, автор не несет ответственности за вред полученный в результате применения материалов сайта, находясь на сайте вы подтверждаете своё согласие с этим. Сделано Хондоводом для Хондоводов. Автор: Илья Серб Все изображения имеют авторство Карта сайта Honda Civic, всем VTEC!